NEW!!! Tweed Bassman Complete Parts Kit!!!
A Beautiful Kit with a Mojo Chassis, High Quality Thordarson Transformers, Sprague 716 Capacitors and Carbon Composition Resistors, Quality Power Supply Capacitors, Quality Switchcraft Jacks, Electro- Harmonix Tubes and High Quality Sockets, all harware and cloth covered wire for that Vintage look. Here is a chance to build a Classic Amplifier -
- Tweed Bassman Kit $585
MOJOTone Tweed Bassman Cabinet - $240
Four Weber VST 10A125 speakers for $384
Assembled and Tone Tested Tweed Bassman Chassis ready for your cabinet - $795 -
We can build any configuration of the Bassman you desire - Mercury Magnetics Transformers - NOS Tubes - Mojo Tweed Series transformers - Any Speaker - Solen Fast Caps - "Whatever You Might Desire" email us with your requests
New!! Tweed Deluxe Reproduction Kit
New!! - Completely Updated Instructions!!!
Deluxe Kit During Assembly
Everything You need to build a custom Tweed Deluxe
Amplifier using the very best available parts
The Kit includes:
1. Tweed Deluxe Mojo Narrow Panel Chassis
with silkscreened faceplate drilled and punched.
2. Vintage Style Transformers by Mojo (We can supply extreme high quality Mercury Magnetics Transformers if desired)
3. Quality Reproduction Tagboard with Rivets
4. Switchcraft Jacks and Carling Switches
5. CTS Potentiometers, Quality Tube Sockets
6. Linecord, Fuseholder , Jeweled Pilot Lamp
7. Sprague Orange Drop (715 Series)and Quality Power Supply Capacitors (Special Sprague 716 or Mallory 150 Series caps $5 extra
8. Carbon Composition resistors and all other parts/wire to complete the chassis (cloth wire add $5)
9. Quality Electro Harmonic 12AX7 and 12Ay7 plus 6V6EH and Sovtek 5Y3 rectifier tube
Ready To Install in Your Custom Cabinet
10. Comes with a COMPLETE 28 page step by step
Professionaly Illustrated Instruction Manual
Deluxe Eyelet Board Front
Rear of Eyelet Board Showing Supply Jumper
Kit before installing Power Transformer
Power Transformer Installed in Chassis
AC and Rectifier Tube Wiring
6.3 Volt Heater Wiring to Tubes
Output Transformer Mounted with Two 6-32 Screws
Backside of Eyelet Board Ready to Install
1 Meg Resistor on Input Jack
Eyelet Board Installed in Chassis
Complete Wiring Underside of Chassis
Finished Chassis Wiring Up Close
Another Closer View Of Chassis Wiring
Completed Amp Top Side
Completed Amp Front
NEW!!!!!!!! Champ
Reproduction Kit
Everything needed to build a complete reproduction of the
Classic Fender(TM) CHAMP
Guitar Amplifier
Parts Kit - (Pictured Above minus the
tubes)
Includes EVERYTHING Needed to build the amplifier chassis
Including a Mojo Chassis, Quality Power Supply Capacitors, carbon composition resistors, high quality transformers,wiring board and all hardware and wire. (for cloth wire add $4, for Sprague 716 or Mallory 150 capacitors add $4 )
All that is required to complete the project is and
cabinet and speaker (see below)
Also includes a reproduction of the original schematic and
chassis layout. This is a parts kit and requires knowlege of
vacuum tube wiring methods, but is not a difficult kit and is
a very good starting point for the beginner.
Champ(TM) Parts Kit $259 (NEW!!! Lower Price)
Weber VST Champ Signature 8S $43
Mojo Reproduction Tweed Cabinet for Tweed Champ - $185
Guitar Tube Reverb Kit
Our latest kit is an electrical reproduction of the famous
Fender tube Reverb from the 1960's. It includes a Webber VST
Chromed Silkscreened Chassis
Hammond Power Transformer, Choke, and ALL
parts required to build a Classic Tube Reverb Unit.
The 6K6GT tube is NOS American made,
not the usual 6V6GT found in most re-issue Reverb units.
A copy of the original Fender Schematic and pictorial
wiring diagrams is included. A Webber VST Tag Board with
eyelets is included. The kit includes pots, resistors
capacitors, wire, Switchcraft jacks, Carling power
switch, pilot lamp assembly, reverb tank, fuseholder, resistors,
cloth wire and all other items required for assembly. This unit can be
used
to add reverb to any amp or you can mount it in a custom case.
This is a not a good starter project for a first time tube builder.
Knowlege of electronic wiring from schematics and soldering is required.
Footswitch assembly is not included. Footswitch assembly is $25
with kit